How to Read Ghosting Direction on a Wide Format Printer
Nov 3, 2026 · 9 min readGhosting rarely means a dead printhead. It shows up as a second edge on text and lines, and a clean nozzle check does not rule it out. Read the offset direction
Read MoreEpson i1600 vs i3200: What the Extra Nozzle Rows Actually Buy
Nov 1, 2026 · 11 min readThe i1600 and the i3200 share one block, one print width and one droplet set. The only real change is nozzle rows, four against eight, so throughput depends on
Read MorePrinthead Cable or Dead Printhead: How to Tell Them Apart
Oct 31, 2026 · 11 min readA printhead cable with a broken conductor looks healthy, so judge by behavior instead of appearance. Print the same short strip at two carriage positions and co
Read MoreEpson SureColor S-Series: Why White and Silver Share One Slot
Oct 29, 2026 · 9 min readAn S80600 has ten ink slots but only nine hold colors. The tenth takes either a White or a Metallic Silver cartridge, never both. Here is how the slot map diffe
Read MorePrints Running Crooked: Roller, Vacuum, or Feed Motor?
Oct 29, 2026 · 11 min readCrooked prints on a roll fed machine come from three places: media pulled at an angle, media gripped unevenly, or media not held flat. Mark both edges at one me
Read MoreRoland XF-640 Heaters: What Each of the Three Zones Does
Oct 28, 2026 · 7 min readThree heater zones on a Roland XF-640 do three different jobs, and the setpoint ranges are narrow on purpose. Here is what the preheater, the print heater and t
Read MoreInk Pooling Under the Printhead: Which Part Is Actually Leaking?
Oct 27, 2026 · 7 min readInk on the printhead nose is usually not a dead printhead. Clean the nozzle plate, park the carriage, and then read when the drip comes back: while idle, mid pr
Read MorePrinthead End of Life: What to Measure Before You Order a New One
Oct 26, 2026 · 9 min readPrinthead life gets counted in months, and that number hides the only variable that matters: how much ink the head has moved. Track ink volume, cleanings per sq
Read MoreWhy a Solvent Printhead Will Not Run UV Ink, and the Three Checks That Tell You Which Chemistry Your Machine Actually Uses
Oct 24, 2026 · 14 min readA printhead that mounts perfectly can still be built for the wrong ink chemistry, and the damage usually shows up weeks later as deflection, seal swelling and d
Read MoreDTF Printer Anatomy: Every Consumable in the Ink Path, Counted One by One From Bottle to Film
Oct 22, 2026 · 9 min readNine components sit between an ink bottle and a sheet of DTF film, and the white channel touches every one. This walk through the ink path names each consumable
Read MoreMimaki JV300 Consumables Map: What to Stock, What to Skip, and How to Set Reorder Triggers Without a Chart
Oct 22, 2026 · 7 min readFollow one JV300 through a working day and the real consumables map writes itself: the moments when a part decides whether the shift finishes on time. Here is w
Read MoreWhich Parts Fit a Mimaki JV300 or a Roland XR-640? How to Build Your Own Cross Reference Instead of Borrowing One
Oct 22, 2026 · 9 min readSearching by printer model is the slowest way to buy a part. This guide shows how to read a machine plate, decode what the old part actually says, ask a supplie
Read MoreThe Encoder Strip: How to Clean It Correctly, and How to Tell When It Is Actually Finished
Oct 22, 2026 · 7 min readA dirty encoder strip mimics a dying printhead, a slipping belt, and a bad carriage board, which is why shops replace the wrong part first. Here is the cleaning
Read MoreHeat Press Settings by Fabric: Cotton, Polyester, Blends, and the Peel Test That Proves Them
Oct 22, 2026 · 7 min readOne transfer, two fabrics, two results. The press settings that work on cotton rarely survive the trip to polyester. This guide swaps the usual chart for a ladd
Read MoreDTF Powder: Mesh Size, Curing Temperature, and the Failures Each One Causes, Told From the Peeling Edge
Oct 22, 2026 · 9 min readMost shops blame the powder for a transfer that peels, then buy a different powder and get the same result. This guide explains what mesh size really controls,
Read MoreRicoh Gen5 vs Gen6: Drop Size, Waveform, and How to Confirm Which Printers Accept Them
Oct 22, 2026 · 8 min readGen5 and Gen6 look like siblings on the bench and behave nothing alike in production. One buys ink latitude and forgiveness, the other buys finer detail and far
Read More