Epson i1600 vs i3200: What the Extra Nozzle Rows Actually Buy
Nov 1, 2026 · 11 min readThe i1600 and the i3200 share one block, one print width and one droplet set. The only real change is nozzle rows, four against eight, so throughput depends on
Read MorePrinthead Cable or Dead Printhead: How to Tell Them Apart
Oct 31, 2026 · 11 min readA printhead cable with a broken conductor looks healthy, so judge by behavior instead of appearance. Print the same short strip at two carriage positions and co
Read MoreHow to Store a Spare Printhead So It Still Works in a Year
Oct 31, 2026 · 8 min readA spare printhead has two halves that want opposite conditions. The nozzles have to stay wet and the circuit board has to stay dry, so drying agents and moistur
Read MoreHow to Apply UV DTF Transfers Without Bubbles or Lifting
Oct 30, 2026 · 10 min readUV DTF transfers fail in three separate places: the print, the lamination, and the hand application. This guide shows how to name the symptom first, why the A f
Read MoreEpson SureColor S-Series: Why White and Silver Share One Slot
Oct 29, 2026 · 9 min readAn S80600 has ten ink slots but only nine hold colors. The tenth takes either a White or a Metallic Silver cartridge, never both. Here is how the slot map diffe
Read MoreKJ4A vs KJ4B: Which Kyocera Head Fits Your Ink?
Oct 29, 2026 · 7 min readKyocera KJ4A and KJ4B printheads share the same footprint, nozzle count and width, but one is built for UV ink and one for water-based. This guide covers how to
Read MorePrints Running Crooked: Roller, Vacuum, or Feed Motor?
Oct 29, 2026 · 11 min readCrooked prints on a roll fed machine come from three places: media pulled at an angle, media gripped unevenly, or media not held flat. Mark both edges at one me
Read MoreInk Pooling Under the Printhead: Which Part Is Actually Leaking?
Oct 27, 2026 · 7 min readInk on the printhead nose is usually not a dead printhead. Clean the nozzle plate, park the carriage, and then read when the drip comes back: while idle, mid pr
Read MoreKM1024i MHE vs LHE vs SHE: Which Variant Fits Your Machine?
Oct 27, 2026 · 11 min readEvery KM1024i variant measures the same on the bench, so the label decides which one your machine needs. This breaks the lineup by drop size, firing frequency a
Read MorePrinthead End of Life: What to Measure Before You Order a New One
Oct 26, 2026 · 9 min readPrinthead life gets counted in months, and that number hides the only variable that matters: how much ink the head has moved. Track ink volume, cleanings per sq
Read MoreWhen Your Shop Turns Dry and the Prints Start Acting Up, Check the Room Before You Blame the Printhead
Oct 24, 2026 · 8 min readDry shop air raises the surface resistance of film, banner and coated stock, and the charge it builds pulls satellite droplets off course onto the nozzle plate
Read MoreWhy a Solvent Printhead Will Not Run UV Ink, and the Three Checks That Tell You Which Chemistry Your Machine Actually Uses
Oct 24, 2026 · 14 min readA printhead that mounts perfectly can still be built for the wrong ink chemistry, and the damage usually shows up weeks later as deflection, seal swelling and d
Read MoreWhat We Learned From Compatible Parts That Failed After Fitting: Six Checks to Run Before You Order for a Wide Format Printer
Oct 23, 2026 · 10 min readCheap parts fail in predictable ways, and most of them are caught before the order ships. Here are the six checks that a working print shop should run on any no
Read MoreHow to Commission a Replacement Printhead on a Wide Format Printer Without Guessing Your Way to a Stable Nozzle Check
Oct 23, 2026 · 13 min readA new printhead that passes one nozzle check and fails by the second production hour is almost never a bad head. This five stage commissioning sequence covers d
Read MoreDTF Printer Anatomy: Every Consumable in the Ink Path, Counted One by One From Bottle to Film
Oct 22, 2026 · 9 min readNine components sit between an ink bottle and a sheet of DTF film, and the white channel touches every one. This walk through the ink path names each consumable
Read MoreThe Encoder Strip: How to Clean It Correctly, and How to Tell When It Is Actually Finished
Oct 22, 2026 · 7 min readA dirty encoder strip mimics a dying printhead, a slipping belt, and a bad carriage board, which is why shops replace the wrong part first. Here is the cleaning
Read More